Jump to the main content
Home Remodel Guidance
Search

Search Home Remodel Guidance

Remodeling Projects You Should Never DIY: A Job-by-Job Chart

Author: Review by Home Remodel Guidance Editorial Team Review date First published Last updated Category: DIY vs. Professional Work

Never DIY structural changes, electrical service and new circuits, gas lines, concealed plumbing, roofing, and anything that disturbs asbestos or lead paint. Painting, trim, tile, cabinets and drywall patching are reasonable DIY projects, and some work sits in between and needs a permit first. The chart below sorts common remodeling jobs into DIY-ok, DIY with permit, and pro only.

Gutted room with a wall opening held by temporary wooden posts and a steel beam above, work light on a tripod

Part of the series: Why Some Renovations Should Always Be Done by Professionals

Some remodeling projects are poor DIY choices, and others are some of the best money-savers in a renovation. This guide gives you the job-by-job view: what is fine to do yourself, what needs a permit, and what to leave to a licensed pro. It is the practical companion to why some renovations should always be done by professionals, which explains the risk, code and licensing reasoning in depth.

Rules differ by city, county and state. The International Residential Code (IRC) is the model most places start from, but local amendments change details, so confirm with your building department.

What are the DIY-ok, DIY-with-permit and pro-only categories?

The three categories sort a job by how much damage a mistake could do and whether the code regulates the work.

  • DIY-ok: low-risk, visible, reversible work with no regulated system involved. Typically permit-exempt finish work.
  • DIY with permit: work you can learn, but where the code requires a permit and inspection, and where some jurisdictions also limit who can do it.
  • Pro only: work where a hidden mistake can injure people or compromise the house, and where licensing, engineering or certification is normally required.

The IRC says an owner or agent must get a permit before constructing, altering or repairing a building or installing or altering a regulated electrical, gas, mechanical or plumbing system (R105.1). It lists finish work such as painting, papering, tiling, carpeting, cabinets and countertops as permit-exempt (R105.2).

Which remodeling projects should you never DIY?

Never DIY the jobs in the pro-only list: structural changes, service-side electrical, gas, relocated plumbing, roofing, and hazardous-material work. The sections below explain the reasoning for each tier.

The comparison table on this page sorts 18 common jobs. Use its verdict column to sort your own project list, then read the reasoning for each tier below.

Structural changes and foundations

Removing a load-bearing wall or repairing a foundation takes an engineer’s design. The IRC states that “ordinary repairs” never include cutting a wall or partition, or cutting or removing a structural beam or load-bearing support (R105.2.2). Read why you need an engineer and a contractor and why foundation issues are not a DIY project.

Electrical service, panels and new circuits

Anything at the service entrance, panel or on new circuits goes to a licensed electrician. The IRC exempts only narrow items such as replacing lamps or a same-size breaker in the same location. Even device swaps should follow the manufacturer’s instructions and your local code, and you should stop and call an electrician if anything looks unfamiliar. See electrical work: when DIY becomes dangerous.

Gas lines and fuel-burning appliances

Gas work is pro only. A bad gas connection can leak fuel, and a badly installed or vented fuel-burning appliance can release carbon monoxide. EPA lists back-drafting from furnaces and gas water heaters, and flues that are improperly sized, blocked or disconnected, among the sources of indoor carbon monoxide. If you smell gas, the American Gas Association says to leave the building immediately with others, avoid anything that could spark, such as lighting a match or using lights or appliances, and call 911 or your gas utility from a safe place away from the area. The IRC exempts only portable appliances and minor parts that do not alter equipment approval; a new line or appliance replacement needs a permit. See HVAC installation and the hidden costs of going DIY.

Plumbing that moves pipes

Swapping a faucet is fine; relocating a drain is not. The IRC exempts stopping leaks, clearing stoppages and reinstalling a toilet, but says replacing a defective concealed drain, water or vent pipe is new work requiring a permit and inspection. Our guide to DIY plumbing limits lists what a homeowner can handle.

Roofing and work at height

Roof work combines falls, weather and water-tightness. OSHA, citing Bureau of Labor Statistics data, reports that falls from elevation caused 389 of 1,034 construction deaths in 2024. Read why roofing repairs belong with the pros.

Asbestos and lead paint

Disturbing asbestos or lead paint calls for testing and certified pros. EPA says you cannot identify asbestos by looking at a material, and recommends testing suspect material that will be disturbed. For pre-1978 homes, EPA recommends a lead-safe certified contractor and a certified inspector or risk assessor to test surfaces. The rule that requires certification applies to firms paid to do the work; it generally does not cover owners working on their own home, but the dust hazard is the same.

Which projects need a permit but can be DIY?

Decks, fences, basement finishing, window replacement and device-level electrical or plumbing swaps often fall here, if your jurisdiction lets owners do the work. The IRC’s permit exemptions include fences not over 7 feet high, and decks not exceeding 200 square feet that are not more than 30 inches above grade at any point, are not attached to a dwelling and do not serve the required exit door. Anything larger, higher, attached or serving an exit door usually needs a permit.

Before you dig for posts or footings, contact 811. 811, the free national before-you-dig service, says to contact 811 before any digging project a few days in advance. Planning guides: building a deck: when to DIY and when to hire out, installing a fence and window installation: why professionals matter. For permit mechanics, see renovation permits: what homeowners need to know.

Which remodeling projects are safe to DIY?

The safest DIY projects are cosmetic and reversible: painting, caulking, trim, tile, cabinets, countertop installation, and small drywall patches. These are all on the IRC’s permit-exempt finish list, though exemption never excuses code violations.

A starter list is in 5 renovation tasks homeowners can safely DIY.

How do big projects split between DIY and pro work?

Most large remodels are mixed jobs, so the smartest plan is to split them by trade: pros for rough-in and regulated work, you for demolition prep, finishes and painting. This is the usual way homeowners save money without taking on the risky parts.

Kitchen remodel

Hire licensed trades for moved gas lines, new circuits, relocated sinks and any wall changes. You can handle painting, backsplash tile, cabinet hardware and, with a helper, cabinet installation. Order matters, so check which renovations to tackle first and the kitchen remodeling starting guide.

Bathroom remodel

Plumbing relocation, shower valve work, new circuits and waterproofing behind tile are the pro-leaning jobs. Demolition prep, painting, vanity and fixture swaps on existing connections, and tile are common DIY. The bathroom remodel cost breakdown shows which line items are labor.

Basement or attic finishing

These projects add framing, electrical, insulation and often egress or ventilation. They need permits almost everywhere. Many owners hire out electrical and any structural work, then do insulation, drywall finishing and paint themselves. Basement finishing: what to consider before you start covers planning.

Is demolition safe to DIY?

Light demolition is a common DIY task, but only after you know what is inside the walls. Before swinging a hammer, find out what runs through the walls (wiring, pipes, ducts), check for a load path above, and test finishes in older homes. EPA says you cannot tell by looking whether a material contains asbestos, and recommends testing materials that will be disturbed. It also says to assume vermiculite insulation contains asbestos and not to disturb it. Lead dust is a separate concern in pre-1978 homes; EPA’s DIY guidance describes plastic containment, misting before sanding, HEPA vacuums and respirators if you do the work yourself.

If a test is positive, stop and hire a licensed abatement or lead-safe certified contractor. Prepare the house first with these steps before renovation begins.

What do insurers and inspectors care about?

Inspectors check that regulated work matches the permit and the code; insurers may ask who did the work and whether it was permitted when a claim involves it. Neither is a reason to avoid DIY on cosmetic jobs, but both are reasons to document permit-required work: keep permits, inspection sign-offs, photos taken before walls close and receipts. Read your homeowners policy and ask your agent before major work; insurance considerations during major renovations lists the questions to ask.

How do you decide for a job that is not on the chart?

Run five checks: structure, regulated system, injury risk, permit and tools. If the job touches structure or a regulated system, or a mistake could injure someone, treat it as permit-and-pro territory. If it needs tools you would use once, compare rental or purchase costs with the quote.

  1. Structure: does it cut, load or support framing?
  2. Regulated system: does it add or alter electrical, gas, mechanical or plumbing?
  3. Injury risk: shock, fire, fall, fumes, dust, or crushing?
  4. Permit: does your building department require one, and can owners pull it?
  5. Skill and tools: can you do it well, and can you afford a redo?

The chart is not the same as a skills self-test. If you want to judge your own readiness, use recognizing your DIY limits, and review the most common DIY renovation mistakes before starting. For the money side, see the true cost of DIY renovations.

What should you do before hiring a pro?

Get written quotes, verify the license, and confirm who pulls the permit. Look up the contractor’s license with your state or local board, request proof of insurance, and put scope, permits and warranty into the contract. Screening questions are in choosing the right contractor: 10 questions to ask, and permits and regulations: why pros get it right explains how inspections work.

Remodeling jobs sorted by who should do them (model-code view; confirm locally)
JobVerdictPermit usually needed?Main reason
Painting, caulking, trimDIY-okNoFinish work; check for lead paint in pre-1978 homes before sanding
Tile backsplash or floor tileDIY-okNoFinish work; waterproofing in wet areas needs care
Cabinet or countertop installationDIY-okNo (plumbing hookups may)Finish work; heavy lifting needs a helper
Small drywall patchDIY-okNoTest first in older homes; see the drywall guide
Hanging and finishing new drywallDIY with permit if walls are newOften, as part of a larger projectSkill-intensive; fire-rated assemblies must be kept
Replacing a faucet or toilet (no pipe changes)DIY-okNoIRC exempts reinstalling a toilet and fixing leaks without rearranging pipe
Swapping a light fixture or outlet in the same spotDIY with permit where requiredVaries by cityFollow the manufacturer's instructions and local code; stop if wiring looks unfamiliar
Replacing windows or exterior doorsDIY with permit (pro suggested)OftenWeatherproofing, headers, heights, lead paint
Building a deck or fenceDIY with permitOften, by size and heightFootings, ledger attachment, utility marking via 811
Insulating an atticDIY with careRarelyCheck for vermiculite (assume asbestos) first
Finishing a basementDIY with permitYes, usuallyEgress, electrical, moisture; framing inspection
Relocating drains, vents or supply linesPro onlyYesConcealed leaks; venting and slope rules
New circuits, panel or service workPro onlyYesFire and shock; service side stays live
Gas line, furnace, boiler or water heaterPro onlyYesFuel leaks and carbon monoxide
Load-bearing wall removal or foundation repairPro only (engineer)YesStructure and load path
Roof replacement or major roof repairPro onlyOftenFalls and water entry
Asbestos or lead abatementPro onlyVariesHazardous dust; certified firms
Digging for footings, posts or trenchesDIY after calling 811VariesBuried utilities; every dig needs an 811 request

Do the finish work yourself, share the rough-in work with licensed trades, and hand the structure, gas, service-side electrical and hazardous materials to professionals.

FAQ

What home projects should you never DIY?

Never DIY load-bearing wall removal, foundation repair, electrical panel or new-circuit work, gas line work, concealed plumbing changes, roof replacement, or any job that disturbs asbestos or lead paint. These involve regulated systems or structure, need permits and inspections in most places, and fail in ways that hurt people or the whole house. Painting, tile, trim and cabinet installation are far lower risk.

Which DIY projects need a permit?

Any project that adds or alters electrical, gas, mechanical or plumbing systems, or changes structure, usually needs one. The model IRC (R105.1) requires a permit for those, and exempts finish work such as painting, tiling, cabinets and countertops. Common permit triggers include adding circuits, moving plumbing, building a deck attached to the house, and finishing a basement. Your local building department has the final word.

Can a homeowner pull their own permit?

It depends on where you live. Whether an owner may pull a permit for their own home, which work they may do personally, and which systems must go to a licensed trade are all set locally, and the model IRC leaves them to the jurisdiction. Call your building department and ask what an owner permit allows before you buy materials.

Is it OK to DIY a bathroom remodel?

Parts of it are. Painting, installing a vanity on existing plumbing, and tiling are common DIY jobs. Moving drains or the shower valve and adding circuits for heaters or new outlets deserve a licensed plumber or electrician and usually a permit, and shower waterproofing should follow your local code. Splitting the job between DIY finish work and pro rough-in work is the usual compromise.

What happens if you do unpermitted work?

Consequences differ by place and by insurance policy, and can include having to open walls for inspection, pay fees, or redo work, and the issue may come up when you sell or file an insurance claim. If you already have unpermitted work, ask your building department what your options are before hiding more work behind drywall.

How do I decide between DIY and hiring a pro?

Ask five questions: does it touch structure or a regulated system, could a mistake injure someone, does it need a permit, do I have the tools and skill, and can I afford a redo? A yes to the first three points to a pro or at least a permit-and-inspect path. Then compare the quote to your tool, material and time costs.

Is DIY drywall safe in an older home?

Patching a small hole is manageable, but sanding or demolishing old wall finishes can release lead or asbestos dust. Test suspect material first, because you cannot identify either hazard by sight. EPA recommends a certified inspector for lead in pre-1978 homes and a trained, accredited professional to sample for asbestos. If the test is positive, hire a licensed abatement or lead-safe contractor.

Sources

  1. 2021 International Residential Code, Chapter 1: Scope and Administration (R105 Permits) (codes.iccsafe.org)
  2. EPA: Renovation, Repair and Painting (RRP) Program: Consumers (epa.gov)
  3. EPA: Lead-Safe Renovations for DIYers (epa.gov)
  4. EPA: I'm remodeling my home. Do I need to be concerned about asbestos in building materials? (epa.gov)
  5. OSHA: National Safety Stand-Down to Prevent Falls in Construction (osha.gov)
  6. EPA: Protect Your Family from Asbestos-Contaminated Vermiculite Insulation (epa.gov)
  7. AGA: Using Natural Gas Safely (aga.org)
  8. EPA: Carbon Monoxide's Impact on Indoor Air Quality (epa.gov)
  9. NFPA: Learn where the NEC is enforced (nfpa.org)
  10. 811: Know what's below. Call before you dig (811beforeyoudig.com)

Related articles

Top of page